But where the variable-intake system in the NRV588 really shows is when you get to 8200 rpm, where maximum torque of 82 ft-lb is delivered, according to Crighton. Here, instead of the midrange flat spot that plagued the older Nortons, the engine keeps pulling hard and continues to accelerate strongly right to the 11,500-rpm limiter. Note that the 165-horsepower number is quoted at 11,450 rpm, which incidentally Crighton says is a conservative figure-he feels 175 horsepower is easily achievable with more development.
The ECU software allows Crighton to dial in a different engine map for wet pavement as well as a different ride-by-wire throttle program and (though it wasn't yet installed for any of my tests) a choice of traction control programs depending on track conditions. With the continuous and overlapping power pulses of the rotary engine making the bike especially prone to wheelspin, this will be a useful feature in the future. It could also allow riders to run a softer rear tire, enhancing traction even more. As it was, even without traction-control programs installed, the NRV's smooth throttle response and linear power made it a confidence-inspiring ride on a wet track-maybe just not as much fun on a dry one.
The bodywork was designed by Harris Performance and painted in colors that recall Norton's classic-era Manx GP singles. The chassis is a Spondon aluminum twin-spar frame based on the '94 Duckhams British Superbike title winner, but because one of Crighton's key objectives in designing the new bike was to maximize the benefits of the rotary engine's compact build, the main spars are 25mm longer to allow for a front-mounted Radtech custom radiator rather than the previous twin side-mounted radiators. This helps reduce the NRV's overall width to just 450mm, more than 50 percent narrower than the old Nortons and not much wider than a 250GP racer. But the rotary engine also has some heat issues caused by the continuous power pulses that can result in exhaust temperatures reaching more than 1000 degrees C. This required a new exhaust system made from costly Inconel alloy, which is more resistant to heat than titanium and is even lighter. Also, to bring cooling air between the rotor housings Crighton borrowed an idea from one of his hobbies. "I fly model aircraft, and they use high-performance duct fans that run at very high speeds and generate lots of airflow," he explains. "There's an electrically driven extractor fan in the duct beneath the seat linked to the ECU, so that as the temperature rises it runs quicker and pulls the heat out of the middle of the engine. The forward ducts on the fairing give a positive effect there, and there's a negative effect at the rear, so you end up with a good cooling airflow. It's the same variable system as the engine's electric water pump, which has no thermostat, just a sensor that monitors engine temperature. As this rises the water pump speeds up, but then it slows down as it cools. It self-regulates so you don't need to tape up the radiator [on colder days]."
 A small electric extractor...  A small electric extractor fan pirated from an R/C model aircraft sits in an underseat duct in the tailsection, helping pull cooling air from between the rotary engine's housings. The fan's variable speed is controlled by the ECU according to engine temperature. |  The air duct running down...  The air duct running down into the area below the fuel injection and airbox pulls cooling air between the rotor housings of the rotary engine, which can generate a staggering amount of heat due to its constant overlapping firing intervals. |  A Yamaha R6 generator attached...  A Yamaha R6 generator attached to the left side of the eccentric shaft powers the Norton's fuel injection and numerous electronic engine and rider aids. This shot also shows the rotary engine's incredibly compact dimensions, evident in the round, exposed case the generator plate is attached to. |
There's just a single Ohlins rear shock on the NRV, offset to the right and operating without any link. "A monoshock with linkage is made very progressive, so it only moves a little when the wheel hits a small bump," says Crighton. "This makes it hard to control the damping accurately, as we proved with back-to-back tests on the Roton GP racer, which became Ian Simpson's title-winning Duckhams Superbike. Our system is better because we have more damping control and better consistency, and the braced swingarm is stiff enough we can move the single shock off to the side to help it run cooler without any flex." Rear-wheel travel is only 3.5 inches, while the wheelbase is extended slightly to 56.1 inches with an increased 54/46 percent front-end bias. The fully adjustable 43mm Ohlins fork is set at a 23.7-degree head angle (adjustable via eccentrics) with 102mm of trail.
This Norton was also the first one I rode with Dymag carbon wheels. As a result the pair of chicanes at Mallory Park, where I tested, suddenly became amazingly easy to flick through. However, I found that the Norton likes to take wide, sweeping lines to maximize turn speed rather than stop, turn and accelerate hard, as you might expect with such a slim, light bike wearing wide, 16.5-inch Dunlop slicks. Edge grip was obviously good on my one dry test day, although one handling aspect I didn't care for was the way the NRV liked to understeer under hard acceleration, perhaps because of the engine power compressing the rear shock without a progressive linkage.
But otherwise the Norton tracked straight and true, and I welcomed the exceptional feel of the radially mounted twin 320mm AP front discs and monoblock four-pad calipers. On a bike this fast on such a tight track you need to have absolute faith in your brake package, and the AP brakes provided it, countering the rotary motor's near-total absence of engine braking. The slipper clutch sourced from a Kawasaki parts bin helped keep the Norton stable as it stopped hard, although it was surely aided by the high 2000-rpm idle speed. The gear-change was a little notchy but nothing oppressive.
 A single Ohlins shock in a...  A single Ohlins shock in a cantilever setup without linkage controls the rear suspension, with the fat rear Dunlop 16.5-inch slick mounted on a wide, 6.5-inch Dymag carbon-fiber wheel. The exhaust system is made entirely from expensive Inconel alloy to withstand the rotary engine's incredibly high exhaust temperatures. |  |  The Wankel rotary's compact...  The Wankel rotary's compact size compared with a conventional four-stroke piston engine is apparent in this bodywork-off photo. Weight bias is 54/46 percent on the front, which helps keep the front tire on the ground when unleashing the Norton's 165 horsepower. |
Sadly, in these days of increasing focus on what are labeled the "spec" classes of racing (production-based categories such as Superbike, Supersport, Superstock, and so on), there's no free-formula racing category where examples of alternative thought like the Norton can be raced. Well, except maybe just one. Back in the '90s, the rotary Nortons regularly raced in the European Battle of the Twins at circuits such as Assen, Monza and Spa-for precisely the reason that the Norton will hopefully be accepted by organizers of such events today, perhaps starting in Daytona in March: It's different.
"It would be nice to run in that kind of racing because of the interest it would create for people who like things that are out of the ordinary," says Crighton. "Whatever the argument is about the capacity, it's a 165-horsepower bike and we're thinking of running it against the 1000cc superbikes producing up to 200 horsepower, so it's a tall order. It'd be incredible if it could be competitive at all, but we're willing to give it a try by using the power-to-weight ratio to our advantage if it's possible. At the moment we've only got the one bike, so if we're going to do any sort of racing we'll need to get a second one built. We do have some spares available, though it is getting a bit difficult with the engine parts now. But we'd like to wave the Norton flag again to show people how a rotary ought to be done right."
Even more to the point, though: How great would a Norton NRV588 street replica be, complete with side ports and fuel injection taking care of emissions (just as it does for Mazda with its RX-8 sports car) and the variable-length intake setup offering superb rideability in a 170-horsepower, 300-pound package?